The world's #1 resource for everything Cummins Turbo Diesel, with a core focus on supporting every individual in a positive environment, regardless of experience and technical ability.

Please take a second to Click here to register, and in a few simple steps you will be able to enjoy a "NO DRAMA" community. Once registered please introduce yourself.

Thank You.
Results 1 to 1 of 1

Thread: How too: Adjust the Bands, 47RE, 48RE, 518, 727 Dodge Transmission with a Cummins

  1. Top Of Page | #1
    Senior Member Polaraco's Avatar
    Join Date
    Oct 2012
    Location
    New Jorsey
    Posts
    4,774
    Truck
    2003 Hugo
    Post Thanks / Like
    Local Date
    09-22-2014
    Local Time
    06:15 PM
    Mentioned
    33 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    124 Post(s)

    How too: Adjust the Bands, 47RE, 48RE, 518, 727 Dodge Transmission with a Cummins

    I am going to do this from memory. My memory is shot, but not that bad. Sorry about no pictures.

    One of the biggest things people overlook is adjusting the bands on their transmission. It's a very important process. That's because they are afraid of it. I have seen the best of mechanics shy away from that stuff.

    I assure you the process is so simple, anybody can do it.

    History
    The 47 and 48RE evolved over the years from the bullet proof 727 3 speed trans of the early 60's. In it's hay day, it was the trans of envy. It evolved to a lock up converter and an overdrive transmission. In the early days, the overdrive units were a problem and the torque converters. But that was designed that way for warranty purposes. In the old days a 727 would take allot of abuse. Considering, they held up pretty well in the diesels too. You couldn't beat it as badly as you could behind a gas motor. The ones that complained, never admitted they beat the crap out of it. Nuff Said

    There are two bands to be concerned with. Some say they should be set two different settings, and some say the same. When you look at the shift process, both bands work pretty hard. I prefer the same adjustment for both since the difference is negligible.

    Remove the transmission pan after draining. In the right rear corner you'll see a round disk about 4" in diameter, with a lever under it, That is a hydraulic servo. In the center of the lever is a nut about 13/16 with a small threaded post in the middle. The nut is a lock nut. On the end of the post is a hex. As I recall it was 5/16 hex.

    Put a socket on the end of the post. With a box wrench, loosen the locking nut. Back the nut down quite a bit. With the socket thread the post in until it bottoms. The manual says 72 In LB. Snug Once you have torqued it down, make note of where the socket handle is pointing. Back the post out 1 and 3/4 turns. Hold the stud still and tighten the locking nut. Done. Now go change your under ware.

    On the left front of the transmission, there is a second adjustment. This one is external of the pan. Repeat the process here as you did inside the pan. It doesn't matter which one is done first. But they both should be done together.

    Fill the trans and yer done!

    Those who tow will probably see 4 to 5 turns before the band bottoms, This is not unusual. But that looseness will cause the bands to wear more and prematurely. There is nothing to do in the over drive unit.

    These transmission flushes are a great idea! They flush the fluid out of the converter which is around 3 quarts. However, the filters need to be changed as well. this is an excellent time to spot wear in the transmission. You want to be looking for chunks of clutch material, brass or aluminum chips laying in the pan and any steel on the magnet in the pan. Black mud stuck to the magnet is normal. Metal pieces are not. Time to stop beating it and keep an eye on it. I've seen these go 50 and 60K from the early warnings. It's your money.

    I'll try to find some pics for you

    Happy Cumminsing
    Last edited by Polaraco; 12-07-2012 at 03:05 PM.

  2. Thanks K-Sons, R3D3L33T thanked for this post
    Likes K-Sons liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Increase your website traffic with Attracta.com